Solutions can be diluted with potable water but distilled water is recommended. Lowest freeze protection is -50°C when diluted 63 parts product to 37 parts distilled water. Most common usage is 60 parts product to 40 parts distilled water.

Use Recommendations

ABLETHERM SR-1 FLUID is a concentrate that once diluted with water can be used in closed loop, water-based HVAC, Process heating and cooling, water-based HVAC, food industry applications within temperature range. Substitute for Dowtherm.

Safety Phrase

Refer Label, TDS or SDS

The post Abletherm SR-1 Fluid appeared first on Able Westchem.

Biocide BS is a versatile product ideal for:

• Controlling slimes, odours, moulds and biological growth in cutting fluids and processing aids.
• As an additive in paints and antifoulants for control of mildew, mould and fungus.
• An effective bilge treatment to control marine plant and animal life such as algae, hydroids and barnacles.

Use Recommendations

BIOCIDE BS is effective at very low concentrations of 12 ppm active ingredient in the control of algae, bacteria and fungi. Recommendations are based with out knowledge of individual water contaminates.

Slug Dosing Recommendations:

When the system is noticeably fouled:

1. 20 to 70ppm for every 4000 Litres.
2. Repeat until microbial control.

Intermittent Maintenance Dosing Recommendations:

1. After establishing microbial control: 13.5 to 80 ppm.
2. Dose 2 to 3 times per week based on microbial control.
3. Sulphate Reducing Bacteria control between 45 to 85 ppm.

Safety Phrase

Refer Label, TDS or SDS

The post Biocide BS appeared first on Able Westchem.

Use Recommendations

Safety Phrase

The post Foamsan – Cleaner Sanitizer Food & Refrigerant appeared first on Able Westchem.

Use Recommendations

RUST CONVERSION (Metal Priming & Preparation)

• Remove oil, grease & loose scale with a free rinsing water based alkaline degreaser such as PREDATOR, TRIPLE 2 or MULTISAFE.
• If necessary strip paint with paint stripper.
• Once surface is paint & free of loose scale dilute PHOSCLEAN 1:3 with potable water to make standard solution (330mls per Litre).
• Apply diluted product to surface & allow to dry in order to penetrate deep rust & to leave surface in a suitable condition for painting with an oil based primer.
• Drying times are variable & are primarily dependent on temperature.
• Note: PHOSCLEAN requires time to chemically destroy rust & it is not necessary to use expensive rust inhibiting paints.
• Zinc rich paints are not recommended.
• PHOSCLEAN like all preventative measures will slow but not stop rust from re-occurring.
• Treated surfaces left uncoated may experience further rusting or flashing so it is important to paint surfaces soon after surface is ready for painting.

SURFACE RUST, BORE STAIN & TARNISHING

• Dilute PHOSCLEAN 1:4 with warn potable water to make standard solution (250mls per Litre).
• Simply submerge the rusty parts, leave for a few minutes & then check until satisfactory.
• Wipe or wash off on completion.
• As it is not always possible to soak surfaces in a bath apply diluted PHOSCLEAN to surface with a damp cloth, sponge or fine steel wool & keep wet.
• Once applied allow time to penetrate & work on surface.
• If surface is porous, prone to runoff or is alkaline (concrete or limestone) a recoat will almost certainly be necessary.
• TIP: Remember surfaces took a long time to scale, rust or encrust & the process to remove this also takes time.

STAIN REMOVING & GENERAL CLEANING

• Dilute up to 1:10 with warm water, however a dilution of 1:4 is recommended for most applications.
• Apply diluted PHOSCLEAN & allow a few minutes to work & then wipe or hose off.
• Do not allow to dry.
• Deeply encrusted stains may need further applications & some slight agitation with a brush or light sourer to promote penetration.
• Remember to keep the surface wet with product & do not allow to dry as process will halt.
• TIP: Always pre test an inconspicuous test area before tackling your job.

CIP CLEANING

• Pre wash using AQIS Alkaline Detergent such as AC222 or Hercules then flush.
• Then use PHOSCLEAN at a dilution to suit your requiremts (from neat to 1:100).
• TIP: Always allow up to 5 minutes of contact time to dissolve scale & precipitates.
• Always rinse food contact surfaces with potable water after use.
• Always pH adjust waste water to pH 7 with sodium hydroxide before release/ disposal.

SITUATIONS TO AVOID IN USE

Safety Phrase

The post Phosclean Descaler appeared first on Able Westchem.