Typical Applications

• Petroleum coke residue removal from ship cargo holds
• Coal, carbon dust and black-stain removal
• Mineral deposit and heavy industrial soil removal
• Preparation of cargo holds between bulk cargoes
• Mould, fungi and algae removal from compatible surfaces
• Foam, pressure-spray, brush, mop, soak or sponge cleaning

Key Benefits

• Industrial-strength, fast-acting formulation
• Foaming action increases contact time on vertical surfaces
• Effective against stubborn pet coke and carbon staining
• Concentrated and adjustable for light or heavy contamination
• Hard-water tolerant
• Australian made and owned

For professional industrial and marine use only. This product is corrosive Class 8 Dangerous Goods and can release toxic gas if mixed with acids. Never mix with acidic cleaners. Use in accordance with the Safety Data Sheet and approved site procedures.

Use Recommendations

The post PET COKE HOLD CLEANER appeared first on Able Westchem.

Use Recommendations

BEERLINE CLEANING:

1. Added to water at ~3-6mls per litre and draw into beer-lines before being allowed to soak for 5-10 minutes.
2. Whilst soaking, agitation by gas injection will assist in loosening soil build-ups from line walls.
3. Once soak time has occurred flush line thoroughly with water before reconnecting to the beer supply.
4. This product is conveniently dyed RED so you can see the product in the lines or solution.
5. Some stubborn lines may require chemical use at a higher concentration.

TANK & VAT CIP CLEANING

Usage rates dependent on task. Kindly see your sales representative for application specific dilutions.

Typical dilutions range from 0.2% to 4% w/w in warm water.

Safety Phrase

Refer Label, TDS or SDS

The post Beerline Cleaner & Cip appeared first on Able Westchem.

Use Recommendations

Use as required. Ensure correct PPE is worn.

Safety Phrase

Refer Label, TDS or SDS

The post EDTA 40% appeared first on Able Westchem.

Use Recommendations

FOAMING ACID CLEANER may be diluted with up to 100 parts of warm to hot water. We recommend a dilution rate of 1 part of FOAMING ACID CLEANER to 5 parts of water initially; this solution can be diluted further or strengthened according to the extent of the contamination. Swab surface, working from the bottom upwards and keep evenly wet until clean. Flush with fresh water. Ensure that the surface is uniformly covered as uneven application may produce streaking.

Safety Phrase

Refer Label, TDS or SDS

The post Foaming Acid Cleaner appeared first on Able Westchem.

Use Recommendations

SOAK OR DIP TANKS (Hooks & Gambrels)

• Dilute: At the ratio of 1 part product to 10 parts water in soak bath.
• Can be used in cold bath but overall performs will be better if the bath is heated to 70-80C.
• TIP: As the contamination within the bath increases extra product will need to be periodically added to offset fat build-up.
• Excessive contamination will require a complete change of dilution bath.Once surface is clean flush clean with copious amounts of potable water.

SMOKE HOUSES

Spray, Foam, Circulate or Brush on with hot water at ratio of 2% to 8% v/v. Agitate and allow 5 to 10 minutes dwell time. Once surface is clean flush clean with copious amounts of potable water.

Safety Phrase

Refer Label, TDS or SDS

The post Hook & CIP Cleaner appeared first on Able Westchem.

Use Recommendations

Safety Phrase

The post Liquid Caustic 50% appeared first on Able Westchem.

Use Recommendations

Use as required with cold or temperate potable water. Typically in use recommendation is 0.5% to 3.5% v/v with potable water for CIP Cleaning.

Safety Phrase

Highly corrosive material, Class 8. Limited life, please use as required. Refer Label, TDS or SDS

The post Nitro Phos – CIP Acid Cleaner appeared first on Able Westchem.

Use Recommendations

SITUATIONS TO AVOID IN USE

Safety Phrase

The post Phosclean Detergent appeared first on Able Westchem.

Use Recommendations

RUST CONVERSION (Metal Priming & Preparation)

• Remove oil, grease & loose scale with a free rinsing water based alkaline degreaser such as PREDATOR, TRIPLE 2 or MULTISAFE.
• If necessary strip paint with paint stripper.
• Once surface is paint & free of loose scale dilute PHOSCLEAN 1:3 with potable water to make standard solution (330mls per Litre).
• Apply diluted product to surface & allow to dry in order to penetrate deep rust & to leave surface in a suitable condition for painting with an oil based primer.
• Drying times are variable & are primarily dependent on temperature.
• Note: PHOSCLEAN requires time to chemically destroy rust & it is not necessary to use expensive rust inhibiting paints.
• Zinc rich paints are not recommended.
• PHOSCLEAN like all preventative measures will slow but not stop rust from re-occurring.
• Treated surfaces left uncoated may experience further rusting or flashing so it is important to paint surfaces soon after surface is ready for painting.

SURFACE RUST, BORE STAIN & TARNISHING

• Dilute PHOSCLEAN 1:4 with warn potable water to make standard solution (250mls per Litre).
• Simply submerge the rusty parts, leave for a few minutes & then check until satisfactory.
• Wipe or wash off on completion.
• As it is not always possible to soak surfaces in a bath apply diluted PHOSCLEAN to surface with a damp cloth, sponge or fine steel wool & keep wet.
• Once applied allow time to penetrate & work on surface.
• If surface is porous, prone to runoff or is alkaline (concrete or limestone) a recoat will almost certainly be necessary.
• TIP: Remember surfaces took a long time to scale, rust or encrust & the process to remove this also takes time.

STAIN REMOVING & GENERAL CLEANING

• Dilute up to 1:10 with warm water, however a dilution of 1:4 is recommended for most applications.
• Apply diluted PHOSCLEAN & allow a few minutes to work & then wipe or hose off.
• Do not allow to dry.
• Deeply encrusted stains may need further applications & some slight agitation with a brush or light sourer to promote penetration.
• Remember to keep the surface wet with product & do not allow to dry as process will halt.
• TIP: Always pre test an inconspicuous test area before tackling your job.

CIP CLEANING

• Pre wash using AQIS Alkaline Detergent such as AC222 or Hercules then flush.
• Then use PHOSCLEAN at a dilution to suit your requiremts (from neat to 1:100).
• TIP: Always allow up to 5 minutes of contact time to dissolve scale & precipitates.
• Always rinse food contact surfaces with potable water after use.
• Always pH adjust waste water to pH 7 with sodium hydroxide before release/ disposal.

SITUATIONS TO AVOID IN USE

Safety Phrase

The post Phosclean Descaler appeared first on Able Westchem.

STONE CONTROL is a concentrated Alkaline but Non-Dangerous product used in very low dilutions of 1-3% with water.

Use Recommendations

Use as required. Ensure correct PPE is worn.

Safety Phrase

Refer Label, TDS or SDS

The post Stone Control – CIP Cleaner appeared first on Able Westchem.

Use Recommendations

Dilute as required – typically used from 1% – 6% depending upon requirements. Always flush cleaned surfaces with copious amounts of potable water before acid cleaning or reusing equipment.

Safety Phrase

Refer Label, TDS or SDS

The post Supa CIP Caustic Cleaner appeared first on Able Westchem.