Typical Applications

• Bore and potable-water treatment
• Industrial water-conditioning systems
• Hardness and scale control
• Iron and metal stabilisation
• Mild-steel corrosion protection
• Improving treated-water clarity and cleanliness

Formulated using NSF/ANSI 60-certified materials and suitable for potable-water applications. Classified as hazardous but not as Dangerous Goods for transport. Use in accordance with the Safety Data Sheet and application-specific technical advice.

Use Recommendations

Safety Phrase

The post AWC WATERCARE PLUS appeared first on Able Westchem.

Use Recommendations

Safety Phrase

The post ABLE Boresafe appeared first on Able Westchem.

Use Recommendations

Use as per technical advice specific to industry only.

Safety Phrase

Refer Label, TDS or SDS

The post Poly Aluminium Chloride PAC50 appeared first on Able Westchem.

Due to its high level of concentrated acids BORE STAIN BEGONE is rated as a Dangerous Good, and should be used with caution, but also confidence that it will remove even the most stubborn bore and rust stains.

Use Recommendations

Bore stain removal & cleaning purposes.

Removing Bore Stains from Bricks, Concrete or Masonry:

1. Thoroughly wet the surface to be cleaned with copious amounts of water.
2. This is important so the product is not sucked into the bricks or masonry which not only wastes product but may emerge later and stain the wall with white acid burn.
3. Once the surface is soaked and does not absorb any more water, dilute 1 part product with 5 parts of water to prepare a diluted solution.
4. Swab or spray the diluted solution onto the surface working from the bottom upwards.
5. Ensure the surface is uniformly covered as uneven application may produce streaks.
6. Keep the surface wet with the product & allow at least 30 minutes to 4 hours depending on the level of contamination to work.
7. If surface starts to become dry apply another coat.
8. The product works via a chemical reaction and the surface to be kept wet with product.
9. Once the bore stain has disappeared flush surface with copious amounts fresh water.
10. For peace of mind and to avoid possible acid burn consider applying 10% Sodium Bicarbonate solution or NEUTRA BRICK afterwards to neutralize the product.

Vanadium stains on brickwork:

1. Green to greenie – yellow Vanadium staining mainly occurs due as natural phenomenon of the raw materials in the bricks and is exacerbated by lower kiln temperatures. Sometime Vanadium stains occur due to incorrect brick cleaning with incorrect or inappropriate brick cleaning acids and neutralizer.
2. Wet brick thoroughly with garden hose.
3. Dilute Bores Stain begone from neat to 1:5 depending on severity. Apply a liberal and even coating and allow 5-10 minutes to work.
4. Agitate with a stiff broom if the Vanadium deposits are thick, and reapply chemical as necessary to keep the stain wet.
5. Rinse off well, then rinse again. Finally apply Neutra Brick to help prevent acid burning.

Rusted Items:

1. Dilute 1 part product with up to 5 parts water.
2. Apply with sprayer or submerge parts into the solution.
3. Allow 30 minutes to 8 hours to work.
4. Check item/s periodical and once rust has been dissolved thoroughly wash the product from the cleaned item.

Items to Avoid:

1. 1. Not typically recommended on Glass, as the strong acids may etch.
   2. Avoid using on galvanized steel.
   3. Avoid using on colorbond window frames, fences etc. A short amount of contact is normally fine (unless in poor condition) but always rinse thoroughly with water.

Safety Phrase

The post Bore Stain Begone – Heavy Duty appeared first on Able Westchem.

Use Recommendations

OXALIC ACID POWDER Cleans new and old timber prior to oiling, staining and painting, when a solution of 1 part Oxalic is added to 10 parts water and applied for 20 minutes then washed of with water.

OXALIC ACID POWDER has some success at removing both bore stains and rust however a purpose made product is nearly always better. To remove bore stains & rust make a solution of 1 part Oxalic to 10 with water and apply. Keep wet for 10 -20 minutes with solution and then wash clean with copious amount of water.

Safety Phrase

Refer Label, TDS or SDS

The post Oxalic Acid Powder appeared first on Able Westchem.